Soldering iron is used in mobile phone repair to fix capacitor resistor diodes, transistor regulators, speaker microphones and mobile displays etc. A 50 watt soldering iron is enough to repair a mobile. When you buy a soldering iron, you have taken into account that when you use a soldering iron, it should not be hotter than where you put it.

There are also many bits supplied with the soldering iron. You have to keep in mind that those wells are interchangeable meaning you can replace them and those bits have to be anti-static so that when you remove or attach a part it doesn't get damaged.

I would recommend using Soldron's iron which I also always use when using this iron, you won't feel the need to use another iron as this iron heats up very quickly and goes mobile. Able to perform all types of repair work

soldering station

Soldering Station, Mobile Repair Tools

There are two things in a soldering station, firstly a stand to hold the iron and secondly, in the iron soldering station you get the option to lower the temperature. Soldering station is better than a normal iron because you have to solder on small parts. You can lower the temperature and when you need to remove the charging socket, you can increase the temperature.

PCB Stand / PCB Holder

PCB Stand / PCB Holder, Mobile Repair Tool

PCB holder is used to hold any kind of motherboard, so when you make repairs on the motherboard, the motherboard does not move here and there are many kinds of PCB stands. In this PCB standard also comes behind low quality and high quality, you only need to use good quality PCB standard.

If the PCP holder is heavy in weight, it is of good quality. If it is light weight, the quality is less.

Best Soldering Wire, Mobile Repair Tools

Solder wire is used to connect the charging terminal or IC or a component in the motherboard to the motherboard. The solder wire can be melted. When iron is applied to it, it is melted and the part or charge control or other part that can be connected to the motherboard is added. There are different types of solder wires.

In plain language, solder wire comes in very thin too, it comes in medium size too and it comes in thick size too. Now the question arises what should you use?

See if you need to install the parts, you use a very fine solder wire and if you want to put a charging socket you can use a medium size solder wire. But you should keep in mind one thing that you should only use good quality solder wire.

The solder wire that is soldered into the solder wire is of good quality. Because when you put the solder wire on the computer, the components are very strong because of the insect, which will not be the insect in the solder wire, the solder wire is not good, I will recommend you to use the solder wire from Bharti company because it In my experience there is very good quality solder wire and it is not very expensive.

Best Multimeter, Mobile Repair Tools

There are two types of multimeters. One is analog and one is digital. Digital multimeter is usually used in mobile repairs. Because digital multimeter is perfect for checking any part or trace because in it we get to know the output value. For mobile repairs, you should use a good quality multimeter. Now the question arises that -

How to check which multimeter is good for mobile repair?

In a multimeter where the positive and negative wires are connected to the beep in continuous mode, the earlier the beep sounds, the better the multimeter. If connecting two wires to a multimeter causes a delay in the sound, that multimeter is not very sensitive.

Antistatic Mat / ESD Mat

Anti-static mat / ESD mat, mobile repair aids

There is an anti-static mat to protect against electric current. Where we do repairs, anti-static mats are placed there and we repair by keeping all the tools on our twitter etc. It has good wiring inside. So that we do not suffer any damage in the event of a sudden power failure.

You have to use this type of mat and it also gives you a separate place to keep mobile repair stuff and the second advantage is that it will not burn if you apply heat or hot air to it. If it doesn't burn, you will benefit too.

Magnifying lamp, mobile repair tool

Magnifying lamps are used to magnify components. But it is not as powerful as a microscope. But it is mostly used because there is a tube lamp in it. If we look inside something, we'll see it grow up, and secondly, through the tubelight, we'll see that part very clearly as well.

It is adjustable, we can change its position whenever and wherever we want. So what should you use in mobile repair?

SMD (Surface Mount Device) / Hot Air Blower

SMD (Surface Mount Device) / Hot Air Blower, Mobile Repair Tool

SMD We can also say hot air blower. It is used to remove and insert components in the motherboard. The components are smd. Can be removed without. But if we use smd If we use, the task of installing and unloading the components is done very quickly. But it should only be used if you can use it, if you use it without learning, it can also damage the motherboard.

SMD There are many types. I would recommend always buying very good quality smd. Use only. Because the better the quality of the SMD, the more power it has to control wind and heat.

Now I will introduce you a toolkit in which you will get all kinds of mobile repair tools. You can take this toolkit with you wherever you go. With the help of which you can earn money by repairing everywhere. All the tools you will find in this tool kit are of good quality.

Precision screwdriver / screwdriver set

If the screw does not open while repairing the smartphone, the Precision Screwdriver will come in handy at that moment. Using a precision screwdriver, we can loosen any type of screw. it also has a magnet

cell phone opener

Mobile phone opener is used to open the body or case of the mobile. Cell phone openers come in two types of materials. First plastic and second metal. You should always use a plastic opener. Plastic opener minimizes the chance of damage. If you are using a metal opener, make sure it is very thin and not too thick and not too thin.

If we open the mobile phone using an opener, the risk of damage to the inside of the mobile is reduced. But when using the opener, keep in mind that the opener doesn't go deep inside.

Brush

Cleaning brushes are not your usual mobile repair brushes. Within these brushes you will also find soft brushes and hard brushes. When we change the display, there is a lot of jam in the body at that time. To remove it we will need a hard brush and if we want to clean the charging socket we will have to use a soft brush there. Therefore, cleaning brush plays a very important role in mobile repair.

now the question arises

Which liquid should we use for cleaning?

 Click image to buy these mobile repair tools

Cleaning brush, mobile repair tool

I suggest you can use gasoline to clean. You can use Phalcon. But don't use thinner at all. Because out of the blue it appears that the phone often dies.

Tweezers

When we repair mobile, we need a twig when installing the component IC or jumper wire. Or we need tweezers when we disconnect the charging connector from the motherboard. Using tweezers, we can detach any component or IC from the motherboard. I suggest that you only use good quality tweezers when repairing cell phones. Use the one whose tip is very thin. When you remove the part, use a thin teacher, and when you remove the charging terminal or IC cover, use a thicker twig.

DC power supply

DC power is used when the mobile phone battery is empty or completely discharged. In that case, a DC power supply is used instead of a battery. If the motherboard in the mobile gets damaged, it will be notified about that as well. We can also extend the battery with DC power supply. There are different types of DC power supplies.

Comes both regular and heavy duty. In general, you can only turn on the phone. Heavy duty DC power also allows you to remove short circuit in the mobile as you can set amps in it. With the help of which you can also remove the short circuit from the phone.

ultrasonic cleaner

In this cleaning box, the motherboard of the mobile phone is cleaned. For this you need to use a special cleaner. What do you get with this cleaning box. You have to pour that cleaner in and turn it on and all the removable parts are mounted on top of the motherboard such as the front camera and the charging lock flex, all these parts have to be disassembled. Just keep the motherboard and put that motherboard in it.

After some time, the motherboard becomes completely clean. If there is water on the motherboard, all the water will drain out. As a result, the condition of the motherboard is completely new.

jumper wire

The tracks are built on top of the motherboard. Sometimes those traces break due to water or dropping the phone. The problem occurs because of the skid mark in the phone. Then those traces are made using jumper wire. Whether the prints on the back of the charging connector are damaged. So jumper wire is used to supply those prints from elsewhere. The jumper wire is just a very thin wire. The thread can be attached anywhere with the help of a shoulder, which removes the color on which the color is applied.

solder paste

Solder paste is used to install the IC. When we put the IC on the motherboard, the IC is reballed before soldering paste. The IC is then placed on top of the motherboard. It also has a lot of quality. When you use solder paste, you have to take one thing into account that you close the lid properly after use. If the casing remains loose, the paste will dry up. There is a paper under the lid, do not throw the paper away and close the lid with that paper. As a result, the solder paste does not spoil quickly.

Paste Flux

When you place a component or charging connector on the motherboard, you use the shoulder. But the solder can't hold it there. Therefore, paste flux is used. If you use good quality Paste Flux. So the stitching is completely fixed and the part or the charging socket or whatever part you install will not come off easily.

Liquid Flux

Liquid pasta is also similar to regular pasta. The only difference is that it is more powerful. When you need to install a part more firmly or on a surface where that part is not attached, you can use liquid paste to fix the part all over.

Thin

Thinner is used to clean the circuit board. Thinner is also known as IPA or isopropyl alcohol in most cell phone repairs. Nowadays there is a lot of mixing. Use a good quality thinner for this. But when you clean the circuit board with its help, do not put the circuit board with the battery connector for at least half an hour. Until the thinner flies well.

Knife cutter

Knife cutters are also used in cell phone repair. You should use a good quality knife cutter. When you install a jumper wire, the jumper wire is cut with a knife cutter or a trace is found on the motherboard even if the knife was cut with a knife cutter. If the blade cutter is of good quality, you can repair the motherboard.

Point cutter

Point milling cutters are widely used in mobile repairs. If the point cutter cuts something in the mobile, the point cutter will cut. You can also remove the jumper wire and IC cover with a point cutter. That is why you make good quality point milling cutters. Because you need it again and again.

Long Nose Pliers

Mobile repair requires long nose pliers to capture every little detail. We can also use tweezers. But if a screw needs to be removed and it won't open with a screwdriver, you'll need to remove it with long-nosed pliers.

Cleaning sponge

Cleaning sponge is used to clean iron pieces. When we use iron, the carbon is deposited on top of the bit. The cleaning sponge is used to clean that carbon, you need to add little water and it will get big or forget about it by itself. Then you can move the iron bit over it and it will clean the iron bit

Desoldering Wick/Desoldering Remover Wick Braid/Soldering Accessory Metallic Tin/Desoldering Wire

D solder wire is used to remove excess solder. Or the charging connector is also used to separate it from the motherboard. This allows you to remove the charger from around the charging socket and when all the solder is used up, the charging socket will automatically detach from the motherboard.

Wristband/Anti-static Wristband for Electronic Components

Anti-static wristband is worn in our hands when we do mobile repairs. As a result, the current generated in the mobile does not go into our body. This does us no damage, nor does it damage the inside of the motherboard, which would be unnecessary. He will enter the field wearing an anti-static wristband. There will be no damage to the motherboard and no damage to you.

Antistatic gloves

Anti-static hand gloves also prevent static current from entering our body. We have no loss while repairing mobile phones.

Anti-static apron

Anti-static apron dress is worn when we do mobile repairs. It prevents static current from entering us.

Smoke observer | smoke extractor | solder vapor absorber

Smoke observer | smoke extractor | Solder vapor trap, mobile repair tools

When we repair a mobile, if it is working with iron or SMD at that time, then smoke comes out. That smoke enters our body through our breath, which is very harmful to our body. That is why smoke detectors are used. The smoke detector's job is to ensure that the smoke that comes out of the smoke sensing device does not end up in our body. Which saves us from the smoke coming from mobile repair. You must also use Smoke Observer.